CamBam
News:
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
December 13, 2018, 14:14:41 pm


Login with username, password and session length


Pages: [1]
  Print  
Author Topic: Speed Wrench  (Read 998 times)
Bob La Londe
CNC Jedi
*****
Offline Offline

Posts: 3418


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« on: November 01, 2018, 22:56:10 pm »

I got tired of busting my knuckles and having to go really slow so I fixed that problem. 

* Speed Wrench.cb (57.25 KB - downloaded 19 times.)

* Speed Wrench.jpg (292.02 KB, 1008x756 - viewed 53 times.)

* Speed Wrench 2.jpg (248.26 KB, 567x756 - viewed 52 times.)

* Speed Wrench 3.jpg (324.36 KB, 1008x756 - viewed 51 times.)
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
dave benson
CNC Jedi
*****
Offline Offline

Posts: 1018


View Profile
« Reply #1 on: November 01, 2018, 23:09:21 pm »

They look really good bob, something I should do as well.
Dave
Logged
Bob La Londe
CNC Jedi
*****
Offline Offline

Posts: 3418


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« Reply #2 on: November 01, 2018, 23:27:05 pm »

My CB file is attached first.  Just adjust for your machine.

After roughing side one I separated them with the bandsaw and decked off the back side with a fly cutter. 

The square hole in the middle of the handles on the side one cut is so I can locate off of it when I flip it over to deck off side two. 
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
dave benson
CNC Jedi
*****
Offline Offline

Posts: 1018


View Profile
« Reply #3 on: November 02, 2018, 06:47:54 am »

Thanks Bob I'll give it a try when I get some more 16 mm ali
Dave
Logged
Garyhlucas
CNC Jedi
*****
Offline Offline

Posts: 1176


View Profile
« Reply #4 on: November 02, 2018, 17:25:56 pm »

I wanted my grandson to be able to take a tool in and out of the spindle.  So I got a cheap right angle style 1/4" drive battery impact wrench.  Installs and removes a tool quickly and I use it to quickly open and close the vises.  Can't use a speed handle because my table is much bigger than the vises so no overhang.  You quickly get the hang of how tight it goes.
Logged

Gary H. Lucas

Have you read my blog?
 http://a-little-business.blogspot.com/
Bob La Londe
CNC Jedi
*****
Offline Offline

Posts: 3418


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« Reply #5 on: November 02, 2018, 18:59:19 pm »

I have a table level enclosure on the table of the KMB1.  I used an air ratchet on those vises when I had them on it.  When I put the larger 8 inch vises on the KMB1 I'll make some holes for a long shank speed handle that I can stick through to reach the vises.  When I close the doors the same metal cover that protects the door slide from chips will cover the holes.  The space will be a little tight to use the air ratchet with the larger vises, and I never really liked it anyway.

I have a bad servo on the KMB1 right now so I'm not in a hurry.  That and its covered in millions of little 4140HT needles. 



* Long Shank Speed Handle.jpg (132.68 KB, 756x1008 - viewed 40 times.)
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
Bob La Londe
CNC Jedi
*****
Offline Offline

Posts: 3418


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« Reply #6 on: November 18, 2018, 00:55:47 am »

https://www.youtube.com/watch?v=cdwUmCX_TSI&feature=youtu.be

The file in the first post is for a 3/4 inch speed wrench.  It has no corner relief for sharp corner screw heads.  There is no fillet between the sections of the wrench either.  The chamfer operation, and the nature of thse unnatural fillets just from cutter diameter resulted in mediocre cutting and burrs from the chamfer tool.  Since I made the first ones for myself, and the vises they were used on actually had rounded corners on the screw heads it was no big deal. 

They work, but a buddy of mine has a 5" vise that uses a 15mm wrench.  The corners on the vise screw head on his vise are sharp, and when I looked at other vises I have I found that most of them have sharp corners on the vise screw head.  I fixed all of that and cut another batch for 15mm.  Attached is that improved file. 

* Speed Wrench 15mm.cb (71.71 KB - downloaded 16 times.)
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines

Valid XHTML 1.0! Valid CSS! Dilber MC Theme by HarzeM
Page created in 0.112 seconds with 19 queries.

Copyright © 2018 HexRay Ltd. | Sitemap