CamBam
News:
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
November 13, 2018, 23:03:43 pm


Login with username, password and session length


Pages: [1]
  Print  
Author Topic: Speed Wrench  (Read 356 times)
Bob La Londe
CNC Jedi
*****
Online Online

Posts: 3385


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« on: November 01, 2018, 22:56:10 pm »

I got tired of busting my knuckles and having to go really slow so I fixed that problem. 

* Speed Wrench.cb (57.25 KB - downloaded 9 times.)

* Speed Wrench.jpg (292.02 KB, 1008x756 - viewed 30 times.)

* Speed Wrench 2.jpg (248.26 KB, 567x756 - viewed 31 times.)

* Speed Wrench 3.jpg (324.36 KB, 1008x756 - viewed 27 times.)
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
dave benson
CNC Jedi
*****
Offline Offline

Posts: 1009


View Profile
« Reply #1 on: November 01, 2018, 23:09:21 pm »

They look really good bob, something I should do as well.
Dave
Logged
Bob La Londe
CNC Jedi
*****
Online Online

Posts: 3385


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« Reply #2 on: November 01, 2018, 23:27:05 pm »

My CB file is attached first.  Just adjust for your machine.

After roughing side one I separated them with the bandsaw and decked off the back side with a fly cutter. 

The square hole in the middle of the handles on the side one cut is so I can locate off of it when I flip it over to deck off side two. 
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
dave benson
CNC Jedi
*****
Offline Offline

Posts: 1009


View Profile
« Reply #3 on: November 02, 2018, 06:47:54 am »

Thanks Bob I'll give it a try when I get some more 16 mm ali
Dave
Logged
Garyhlucas
CNC Jedi
*****
Offline Offline

Posts: 1169


View Profile
« Reply #4 on: November 02, 2018, 17:25:56 pm »

I wanted my grandson to be able to take a tool in and out of the spindle.  So I got a cheap right angle style 1/4" drive battery impact wrench.  Installs and removes a tool quickly and I use it to quickly open and close the vises.  Can't use a speed handle because my table is much bigger than the vises so no overhang.  You quickly get the hang of how tight it goes.
Logged

Gary H. Lucas

Have you read my blog?
 http://a-little-business.blogspot.com/
Bob La Londe
CNC Jedi
*****
Online Online

Posts: 3385


^ 8.5 pounds on my own hand poured bait.


View Profile WWW
« Reply #5 on: November 02, 2018, 18:59:19 pm »

I have a table level enclosure on the table of the KMB1.  I used an air ratchet on those vises when I had them on it.  When I put the larger 8 inch vises on the KMB1 I'll make some holes for a long shank speed handle that I can stick through to reach the vises.  When I close the doors the same metal cover that protects the door slide from chips will cover the holes.  The space will be a little tight to use the air ratchet with the larger vises, and I never really liked it anyway.

I have a bad servo on the KMB1 right now so I'm not in a hurry.  That and its covered in millions of little 4140HT needles. 



* Long Shank Speed Handle.jpg (132.68 KB, 756x1008 - viewed 17 times.)
Logged

Getting started on CNC?  In or passing through my area?
If I have the time I'll be glad to show you a little in my shop. 

Some Stuff I Make with CamBam
http://www.CNCMOLDS.com
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines

Valid XHTML 1.0! Valid CSS! Dilber MC Theme by HarzeM
Page created in 0.103 seconds with 19 queries.

Copyright © 2018 HexRay Ltd. | Sitemap